1、Upper Bound Analysis of Extrusion of a Spline Shaft
花鍵軸擠壓的上限分析

2、It can be made by blowing, extrusion casting, solution casting, or by calendaring.
可通過吹膜、擠壓鑄造、溶液鑄造或軋光工藝制造。

3、Objective: To improve ct diagnostic value of extrusion disc in intervertebral foramen.
目的：提高對椎間孔內腰椎間盤突出的CT診斷及臨床意義的認識。

4、A flexible, toughened, low moisture absorption polyamide 612 resin for extrusion applications.
一個靈活的，增韌，尼龍612樹脂擠出應用低水分的吸收。

5、Effect of chlorinated polyethylene on rigid polyvinyl chloride extrusion is studied.
研究了氯化聚乙烯(CPE)對硬質聚氯乙烯擠出性能的影響。

6、At the same time the Brabender extrusion behaviour was also studied.
同時對共混體的擠出加工性能進行了研究。

7、THE HIGH SPEED EXTRUSION TECHNOLOGY OF PE CABLE MATERIAL
聚乙烯電纜料的高速擠出技術

8、Analysis of Cold Extrusion Die by Finite Elements
冷擠壓模的有限元分析

9、Applicable to screw extrusion particles, rock particles, high-speed mixed granulation particles.
適用于螺桿擠壓顆粒、搖擺顆粒、高速混合制粒顆粒。

10、Fibrous tissue formed by extrusion is the main reason of the anisotropy in L and LT directions.
擠壓形成的纖維組織是引起擠壓帶板L向及LT向各向異性的主要原因。

11、Influence of extrusion process on grain size of AK_(4-1ч) rod
擠壓工藝對AK_(4-1ч)合金棒材晶粒大小的影響

12、E: Extrusion nozzle.
E：擠出嘴(見樣品)。

13、Rugged aluminum extrusion supports the linear rail system through the entire stroke length.
堅固的鋁擠壓支持通過整個行程長度的直線鐵路系統。

14、Design of Forward Extrusion Trimming Die for Drawing-Type Bush
抽動式襯套正擠切邊模設計

15、Why this three screw extrusion machine has such a powerful plasticizing dispersion function?
為什么這種三螺桿擠出機具有如此強大的塑化分散功能呢？

16、Extrusion Process of Multi-oriffice Plastic Pipes and Its Die Head
多孔塑料管材擠出工藝和機頭模具

17、We also produce the following projects: Injection Product, Extrusion Product, and Die Cast Product.
我們還生產以下項目：注塑產品、塑產品、鋁產品。

18、In this paper, the coining of turbine static-blade formed by lateral extrusion is researched.
本文對徑向擠壓成形的汽輪機靜葉片進行了精壓工藝研究。

19、Study on the Stress Distribution of Cold Extrusion Die under Inner Pressure
冷擠壓模受內壓作用應力分布規律的研究

20、The main cause for arcing is the severe extrusion and abrasion on the fixed part of the wires.
而導致這兩根導線之間產生電弧的直接原因則是導線在固定卡子部位出現了嚴重擠壓和磨損。

21、Study of the high speed extrusion property of PE for telephone cable
聚乙烯絕緣市話電纜高速絕緣擠出性能研究

22、The extrusion and injection conditions of the flame-retardant POM were the same as common POM.
注塑時宜采用螺桿式注塑機，擠出和注射成型的工藝條件與普通POM相同。

23、There are lots of advantages by cold extrusion for straight knurl nut in a single process.
直紋滾花螺母采用冷擠壓一次成形新工藝，成效顯著。

24、The key is how to heat up the cold feed extruder equably and improve extrusion efficiency.
但關鍵問題是如何使冷喂料擠出均勻加熱，如何保證擠出質量，提高擠出效率。

25、Carriage: Guided and Supported, body extrusion geometry, supports carriage motion.
運輸：引導和支持，身體擠出幾何，支持運輸的議案。

26、Optimization of die bearing for aluminum profile extrusion die
鋁型材擠壓模工作帶優化

27、Study of the Mechanism of Wall Slip in an Extrusion Dic of Polymer Melts
擠出口模內壁面滑移機理研究

28、Technology of Liquild Extrusion for Aluminium Alloy oil Pump Body of Car
轎車鋁合金油泵殼體液態擠壓工藝

29、Application of 65Cr4W3Mo2VNb Steel in Heat Extrusion Die
65Cr4W3Mo2VNb鋼在熱擠壓模具上的應用

30、Life and failure analysis on hot extrusion die for bearing rings
套圈熱擠壓模具失效分析

extrusion翻譯

n. 擠出, 推出, 趕出【化】 擠出; 擠塑; 壓出【醫】 上超Ж, 上超咬合 詳情